BEIYANG BTP-2200E WIN7 DRIVER


If users need the further data about these products, please feel free to contact our market department or your local distributor. If the printer is idle for a long period, please disconnect the power. The figure above takes the marked paper as an example to show the print and paper out position; Non-continuous paper is positioned based on the front edge of marks; The position adjustment of the print and paper out refer to Figure 3. User can also choose USB interface to replace Parallel interface. Print pattern hall not move when it is less than 4 dots, or the print pattern shall move based on 8 dots when it is between 4 dots and 8 dots.

Uploader: Vutilar
Date Added: 18 October 2006
File Size: 13.90 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 15662
Price: Free* [*Free Regsitration Required]

SNBC BTPE BPLE Printer Drivers – Download Device Drivers – –

You also can download bfiyang driver from our website www. Select the print mode: User can also choose USB interface to replace Parallel interface. Provides important information and prompts for printer operation. The mount of ribbon output shaft is finished. In case that this happens, turn off the power immediately. All rights are reserved. If the print finishes just now, please wait for the THP cool down completely; 3 4 Clean away dusts or dirt on the THP with alcohol tampon should twisted ; Wait for 5 to 10 minutes until alcohol volatilizes completely, then press down ribbon holder and close top cover.

Power LED always light. Then the print job stops, the host fails to communicate with the printer.

Are now able to get a CA driver’s license. How to add a network printer using Windows 7 – Duration.

  CONEXANT/ROCKWELL 56K V.92 PCI MODEM DRIVER DOWNLOAD

Driver BTPE(BPLE)(U)1 for Windows 7

When connecting USB interface printer to the host, the system identifies USB device automatically and pop up wib7 driver installation guide. If the print just finishes, you should wait for the platen cool down completely; 3 4 Clean away dusts or dirt on the transmission sensor with alcohol tampon should twisted ; Wait for 5 to 10 minutes until alcohol volatilizes completely, then press down ribbon holder and close top cover.

In the following cases, the media needs to be verified before the print: Adjust the tear-off position in vertical direction with one dot as a motion unit. Drop paper roll on the paper holder to the paper room, then pull out the front end of the paper and put it in the print path flatly, and also release the paper guide to hold it. Only way to the one that did not get the best drivers in.

PRINTER, BTP-2002NP

Error LED status Two flashes Reasons THP is lifted up Micro-switch fault Paper roll is end or no paper roll is loaded Paper jam Paper roll surface is dirty or damaged Settlement Please press down the THP Contact with maintenance people Load paper roll Remove paper jam Please cross over dirty or damaged part Load paper roll again Clean marked paper sensor surface Set paper type in the printer driver is same with actual paper type Make communication cable connection firmly Set the communication interface of the print consisting with that of PC Such as: Please check flash times of LED, then refer to the table as below to settle it: Figure G shows the tear-off position upwards, which should be adjusted in negative direction; Figure H shows the tear-off position downwards, which should be adjusted in positive direction; 4 Routine maintenance of the printer Follow the steps as below to clean the THP, platen and sensor monthly.

  EETOOLS CHIPMAX2 DRIVER

The steps for cleaning the THP are as below: Adjust the printout in vertical direction with 1 dot as a motion unit.

Safety instruction Before installing and using the printer, please read the following items carefully.

After pressing pause key, the printer shall exit pause status and print; 3 If the checkout fails, the printer shall alarm: Windows 10, Windows 8. If any part is short or damaged, please contact with our distributor beiyanh manufacturer. The print side should be upside.

nanesleso.c0.pl

To select thermal transfer mode, you need to mount ribbon; To select thermal mode, no need to mount ribbon; In normal condition, ribbon width should be bigger than the paper width; During this mount, the ribbon should not be cockled or damaged.

When turning the knob in clockwise, the THP pressure increases along with level bbeiyang.

How to install a driver manually. Please refer to 2. If this THP still fail to work properly, please contact with our distributor or manufacture. Como encontrar driver e programa para ativar ou. Different compounding of the three LEDs means different setting.

Why do I need to update drivers?