E510 PCI DRIVER


Ensure that you release the securing tab to unseat the card. Reversing the cable prevents the drive from operating and could damage the controller, the drive, or both. When installing the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage. If you are installing a PCI Express x16 card, the card may cover the floppy-drive connectors. If you installed a processor replacement kit from Dell, return the original heat-sink assembly and processor to Dell in the same package in which your replacement kit was sent. If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. DDR2 memory modules should be installed in pairs of matched memory size, speed, and technology.

Uploader: Juzilkree
Date Added: 18 May 2009
File Size: 49.27 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 34943
Price: Free* [*Free Regsitration Required]

Specifications: Dell Dimension /E Service Manual

Certain components within the computer require address space in the 4-GB range. When removing or replacing the processor, do not touch any of the pins inside the processor socket or allow any objects to fall onto the pins in the socket. Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Media Oci Reader Optional.

Gently pull the securing tab, grasp the card by its top corners, and then ease it out of its connector. Use the pull-tab to remove the data cable from your hard drive or from the system board.

If you remove your original memory modules from w510 computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. For additional information on the type of memory supported by your computer, see your Owner’s Manual. To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.

  MAGICSCAN MAC DRIVER

Dell Dimension

To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer. To avoid damage, ensure that the processor aligns properly with the socket, and do not use excessive force when you install the processor. When installing the processor, do not touch any of the pins inside the socket or allow any objects to fall onto the pins in the socket.

See the documentation that came with the drive for instructions on installing any software required for drive operation.

If you are installing pcu replacing a PCI Express card, follow the procedures in the next section. If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you replace the processor. If the DDR2 memory modules are not installed in matched pairs, the computer will continue to operate, but with a slight reduction in performance.

To loosen the two captive screws on each side of the heat-sink assembly, you need a long Phillips screwdriver. If necessary, disconnect any cables connected to the card. Ensure that the tab on the processor cover is positioned underneath the release lever at the front of the socket.

To connect a network cable, first plug the cable into the network port or device and then plug it into the computer. Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. The pin-1 end of a connector on a board cpi a card is usually indicated by a silk-screened “1” printed directly on the board or card.

  DWA-552 XTREMEN DESKTOP ADAPTER DRIVER

Leave the release lever extended in the release position so that the socket is ready for the new processor. While you work, periodically touch an unpainted metal surface to dissipate any static electricity that could harm internal components.

Instead, set the drive on a surface, such as a foam pad, that will sufficiently cushion it.

If you are installing a PCI Express x16 card, the card may cover the floppy-drive connectors. Grasp the card by its top corners, and ease it out of its connector. Do not set the heat-sink assembly upright or touch the thermal interface, as this may result in damage to the thermal interface material. Ensure that you release the securing tab to unseat the card.

To connect a network cable, first plug pfi cable pck the network port or device, and then plug the cable into the computer.

Your computer supports DDR2 memory. You must route the DC power cables properly through the routing clips when you replace the cables to prevent them from being pinched or crimped. If e5510 new floppy drive does not include shoulder screws, use the screws within the drive panel insert.

If you are installing a new drive, you need to remove the drive-panel insert. See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting.